Δείτε τις προδιαγραφές για λεπτομέρειες προϊόντος.
TSOP6256TR
Introduction
The TSOP6256TR is a component belonging to the category of infrared receivers. This device is commonly used in remote control systems for various electronic appliances, offering specific characteristics and features that make it suitable for such applications.
Basic Information Overview
- Category: Infrared Receiver
- Use: Remote Control Systems
- Characteristics: High sensitivity, low power consumption
- Package: 3-pin epoxy package
- Essence: Detecting infrared signals from remote controls
- Packaging/Quantity: Available in reels with varying quantities
Specifications
- Operating Voltage: 2.5V to 5.5V
- Carrier Frequency: 56kHz
- Supply Current: 350µA
- Transmission Range: Up to 45 meters
- Output Signal: Active low
- Operating Temperature: -25°C to 85°C
Detailed Pin Configuration
The TSOP6256TR has a 3-pin configuration: 1. OUT (Pin 1): Output 2. GND (Pin 2): Ground 3. VS (Pin 3): Supply Voltage
Functional Features
- High immunity against ambient light
- Improved shielding against electrical field disturbances
- Low power consumption
- Photodetector and preamplifier in one package
Advantages and Disadvantages
Advantages
- Reliable detection of infrared signals
- Wide operating voltage range
- Long transmission range
- Low power consumption
Disadvantages
- Limited carrier frequency compatibility
- Susceptible to direct sunlight interference
Working Principles
The TSOP6256TR operates based on the principle of detecting modulated infrared signals. When exposed to infrared radiation at its carrier frequency, the device produces a corresponding output signal, which can be utilized for remote control applications.
Detailed Application Field Plans
The TSOP6256TR is widely used in various consumer electronics, including televisions, air conditioners, audio systems, and other remote-controlled devices. Additionally, it finds application in industrial automation and smart home systems.
Detailed and Complete Alternative Models
- TSOP4838: Similar characteristics, lower supply current
- TSOP38438: Enhanced immunity to ambient light, wider operating temperature range
- TSOP2238: Lower supply voltage, reduced transmission range
In conclusion, the TSOP6256TR is a versatile infrared receiver suitable for remote control systems in both consumer electronics and industrial applications. Its high sensitivity, low power consumption, and reliable performance make it a preferred choice for designers and manufacturers seeking efficient remote control solutions.
Καταγράψτε 10 συνήθεις ερωτήσεις και απαντήσεις που σχετίζονται με την εφαρμογή του TSOP6256TR σε τεχνικές λύσεις
What is TSOP6256TR?
- TSOP6256TR is a miniaturized IR receiver module for infrared remote control systems.
What is the operating voltage range of TSOP6256TR?
- The operating voltage range of TSOP6256TR is typically 2.5V to 5.5V.
What is the typical reception range of TSOP6256TR?
- The typical reception range of TSOP6256TR is around 45 meters.
What is the carrier frequency range supported by TSOP6256TR?
- TSOP6256TR supports a carrier frequency range of 30 kHz to 56 kHz.
What is the output signal format of TSOP6256TR?
- The output signal format of TSOP6256TR is active low.
What is the typical supply current of TSOP6256TR?
- The typical supply current of TSOP6256TR is around 350 µA.
What is the recommended operating temperature range for TSOP6256TR?
- The recommended operating temperature range for TSOP6256TR is -25°C to 85°C.
Can TSOP6256TR be used in battery-powered applications?
- Yes, TSOP6256TR's low power consumption makes it suitable for battery-powered applications.
Does TSOP6256TR have any built-in filtering for noise suppression?
- Yes, TSOP6256TR has built-in automatic gain control and a bandpass filter for robustness against disturbances.
Is TSOP6256TR compatible with standard microcontrollers and IR protocols?
- Yes, TSOP6256TR is compatible with most standard microcontrollers and common IR protocols, making it versatile for various technical solutions.